Do you have a Rad Power Bike whose throttle isn’t working You’re not alone. This is a common problem, and it can be frustrating and inconvenient. But don’t worry, there’s a fix. In this guide, I’ll walk you through the steps to troubleshoot and repair your Rad Power Bike throttle. I’ll also provide some tips on how to prevent this problem from happening again. So if your Rad Power Bike throttle isn’t working, read on for help!
Most Common Reasons: Rad Power Bike Throttle Not Working
Most Common Reasons: Rad Power Bike Throttle Not Working
Throttle cable is not connected properly
The throttle cable may be disconnected from the throttle housing or the motor.
Check to make sure that the cable is securely connected to both the throttle housing and the motor.
If the cable is disconnected, reconnect it and tighten the screws securely.
Throttle cable is frayed or damaged
The throttle cable may be frayed or damaged, which can prevent it from working properly.
Check the throttle cable for any signs of fraying or damage.
If the cable is damaged, replace it with a new one.
Throttle housing is damaged
The throttle housing may be damaged, which can prevent the throttle from working properly.
Check the throttle housing for any signs of damage.
If the housing is damaged, replace it with a new one.
Throttle sensor is dirty or damaged
The throttle sensor may be dirty or damaged, which can prevent it from working properly.
Clean the throttle sensor with a soft cloth.
If the sensor is damaged, replace it with a new one.
Throttle control unit is not working properly
The throttle control unit may not be working properly, which can prevent the throttle from working.
Check the throttle control unit for any signs of damage or malfunction.
If the control unit is not working properly, replace it with a new one.
How to Troubleshoot: rad power bike throttle not working
Symptoms of a Rad Power Bike Throttle Not Working
There are a few different symptoms that can indicate that the throttle on your Rad Power Bike is not working properly. These include:
The throttle does not engage when you twist the grip.
The throttle engages and disengages intermittently.
The throttle does not provide smooth acceleration.
The throttle causes the motor to rev up and down without actually moving the bike.
If you are experiencing any of these symptoms, it is likely that there is something wrong with the throttle itself or with the wiring that connects it to the motor.
How to Fix a Rad Power Bike Throttle Not Working
There are a few different things that you can check to try to fix a Rad Power Bike throttle that is not working.
1. Check the throttle cable
The first thing you should do is check the throttle cable to make sure that it is not damaged or frayed. If the cable is damaged, you will need to replace it.
To check the throttle cable, follow these steps:
1. Remove the handlebar grips.
2. Locate the throttle cable. It is a black cable that runs from the throttle grip to the motor.
3. Inspect the cable for any damage. Look for fraying, kinks, or breaks.
4. If the cable is damaged, replace it with a new one.
2. Check the throttle sensor
The throttle sensor is a small electronic device that is located near the throttle grip. It sends a signal to the motor when you twist the throttle grip.
To check the throttle sensor, follow these steps:
1. Turn off the bike and disconnect the battery.
2. Locate the throttle sensor. It is a small black box that is attached to the handlebar near the throttle grip.
3. Use a multimeter to check the resistance of the throttle sensor. The resistance should be between 100 and 200 ohms.
4. If the resistance is not within the specified range, replace the throttle sensor.
3. Check the wiring
The throttle is connected to the motor by a set of wires. If any of these wires are damaged or disconnected, the throttle will not work properly.
To check the wiring, follow these steps:
1. Turn off the bike and disconnect the battery.
2. Locate the throttle wires. They are a set of black wires that run from the throttle grip to the motor.
3. Inspect the wires for any damage. Look for fraying, kinks, or breaks.
4. If any of the wires are damaged, replace them.
5. Reconnect the battery and turn on the bike.
4. Reset the throttle
If you have checked all of the above and the throttle is still not working, you may need to reset it.
To reset the throttle, follow these steps:
1. Turn off the bike and disconnect the battery.
2. Locate the throttle reset button. It is a small black button that is located near the throttle grip.
3. Press and hold the reset button for 5 seconds.
4. Reconnect the battery and turn on the bike.
The throttle should now be working properly.
Additional Tips
If you are not comfortable working on your bike, you can take it to a qualified bike mechanic for repairs.
When troubleshooting a throttle problem, it is important to be methodical and to check each potential cause one by one.
If you are unable to fix the throttle yourself, you can contact Rad Power Bikes for support.
Conclusion
The throttle is an important part of your Rad Power Bike. If it is not working properly, it can be dangerous to ride the bike. By following the steps in this article, you can troubleshoot and fix a throttle problem yourself.
You May Like to Read: Bike Dropper Post Not Working
