Do you have a Myx bike and your cadence sensor isn’t working
You’re not alone. This is a common problem that can be frustrating and inconvenient, but it’s also easy to fix. In this guide, I’ll walk you through the steps to troubleshoot and repair your cadence sensor so you can get back to enjoying your bike.
Most Common Reasons: Myx Bike Cadence Sensor Not Working
Cadence Sensor Not Attached Properly
The cadence sensor is a small device that attaches to the crank arm of your bike. It sends a signal to the bike computer, which then displays your cadence revolutions per minute on the screen. If the cadence sensor is not attached properly, it will not be able to send a signal to the bike computer and your cadence will not be displayed.
To check if the cadence sensor is attached properly, follow these steps:
1. Turn off your bike computer.
2. Remove the rubber cap from the end of the crank arm.
3. Look for a small screw on the end of the crank arm.
4. If the screw is not there, or if it is loose, tighten it with a small Allen wrench.
5. Reattach the rubber cap.
6. Turn on your bike computer.
If your cadence is still not displayed, you may need to replace the cadence sensor.
Cadence Sensor Not Aligned Properly
The cadence sensor needs to be aligned properly with the magnet on the crank arm in order to work properly. If the sensor is not aligned correctly, it will not be able to send a signal to the bike computer and your cadence will not be displayed.
To check if the cadence sensor is aligned properly, follow these steps:
1. Turn off your bike computer.
2. Remove the rubber cap from the end of the crank arm.
3. Look for a small magnet on the end of the crank arm.
4. The magnet should be located directly in front of the cadence sensor.
5. If the magnet is not located directly in front of the cadence sensor, adjust the position of the cadence sensor until it is.
6. Reattach the rubber cap.
7. Turn on your bike computer.
If your cadence is still not displayed, you may need to replace the cadence sensor.
Cadence Sensor Dirty or Damaged
The cadence sensor can become dirty or damaged over time, which can prevent it from working properly. If the cadence sensor is dirty, you can clean it with a dry cloth. If the cadence sensor is damaged, you will need to replace it.
To check if the cadence sensor is dirty or damaged, follow these steps:
1. Turn off your bike computer.
2. Remove the rubber cap from the end of the crank arm.
3. Look at the cadence sensor.
4. If the cadence sensor is dirty, clean it with a dry cloth.
5. If the cadence sensor is damaged, replace it.
6. Reattach the rubber cap.
7. Turn on your bike computer.
If your cadence is still not displayed, you may need to replace the cadence sensor.
Cadence Sensor Battery Low
The cadence sensor is powered by a battery. If the battery is low, the cadence sensor will not be able to send a signal to the bike computer and your cadence will not be displayed.
To check if the cadence sensor battery is low, follow these steps:
1. Turn off your bike computer.
2. Remove the rubber cap from the end of the crank arm.
3. Look for a small battery compartment on the cadence sensor.
4. If the battery is low, replace it.
5. Reattach the rubber cap.
6. Turn on your bike computer.
If your cadence is still not displayed, you may need to replace the cadence sensor.
How to Troubleshoot: myx bike cadence sensor not working
Symptoms
There are a few different symptoms that may indicate that your myx bike cadence sensor is not working properly. These include:
The cadence reading on your bike computer is not accurate or does not appear at all.
The cadence sensor light is not blinking.
The cadence sensor is loose or not properly attached to the bike.
The cadence sensor is damaged.
Troubleshooting
If you are experiencing any of the symptoms listed above, you can try troubleshooting the problem yourself by following these steps:
1. Check the battery in your bike computer:
If the battery is low, it may be causing the cadence reading to be inaccurate or not appear at all. Replace the battery and see if the problem is resolved.
2. Check the cadence sensor light:
The cadence sensor light should be blinking when you are pedaling. If the light is not blinking, the sensor may be loose or not properly attached to the bike.3. Check the cadence sensor connection:
The cadence sensor connects to the bike computer via a wire. Make sure that the wire is securely connected to both the sensor and the computer.
4. Inspect the cadence sensor for damage:
If the cadence sensor is damaged, it will need to be replaced.
How to Fix: myx bike cadence sensor not working
If you have tried troubleshooting the problem yourself and the issue persists, you will need to take your bike to a qualified bike mechanic for repairs. The mechanic will be able to diagnose the problem and make the necessary repairs.
Additional Resources
[How to Troubleshoot a Bike Cadence Sensor](https://www.bicycleretailer.com/tech/2018/05/03/how-troubleshoot-bike-cadence-sensor)
[How to Replace a Bike Cadence Sensor](https://www.parktool.com/blog/repair-help/cadence-sensor-replacement)
[Bike Cadence Sensor Buying Guide](https://www.rei.com/learn/expert-advice/bike-cadence-sensor-buying-guide)
You May Like to Read: Nordictrack Bike Display Not Working
